Archived from groups: alt.video.satellite.4dtv (
More info?)
Hi,
Again I thank you for your response.
Nothing has really changed with the receivers. Methinks it's time to call
the service guy and have him come out and adjust the dish. It's been a long
time since anything has been done to it. He can look at all the settings
and connections with the receivers at the same time.
I do really appreciate all your input!
--
Kathy
aka smiley
In God We Trust
"Valdivar" <rebelleader68@hotmail.com> wrote in message
news:hTu8e.100$9G.23050@news20.bellglobal.com...
> You don't tweak anything on the 905,because it doesn't move the dish.The
> only thing you would do with it is set the right settings.
>
> (btw: hopefully,you have the polarity wires still hooked up to your analog
> receiver -if not you may have problems as the 905 doesn't like to give
> control back to the analog receiver)..
>
> Use your analog receiver to peak your dish and skew.
>
> On your 905 check that you have selected the right dish settings for your
> feedhorn and servo,etc.
>
> If you've done all the above,try replacing the coax patch cable between
> the 905 and the analog receiver(assuming you've got the cables hooked up
> right)....you could have a bad cable.
> "Smiley" <smiley@cheerful.com> wrote in message
> news:d3tqds$1v0k$1@news.iquest.net...
>> Thank you for your response. I'm going to try the "keying" but when I
>> select OPTIONS 6,4,4...
>>
>> OPTIONS
>> 6 Change system settings
>> 4 Check system status
>>
>> ...there is no 4 in this list. But it shows Signal Quality: 1. Thee
>> doesn't seem to be a way to tweak anything from this menu. What do you
>> mean by "keying" the satellite?
>>
>> Here're my options:
>> OPTIONS
>> 6 Change system settings
>> 3 Change installation settings
>> 1 Set remote control address
>> 2 LNB type
>> 3 feedhorn polarization
>> 4 Memorize useable satellites I tried this one but don't see how to
>> tweak settings
>> 5 update to latest IRD software
>>
>> --
>> Kathy
>> aka smiley
>>
>> In God We Trust
>> "SAC 441" <SAC441@webtv.net> wrote in message
>> news:16414-4261465B-82@storefull-3255.bay.webtv.net...
>>> In my experience,the persistent message that says,"Please Wait A
>>> Moment...We Are Processing Your Request" 80% of the time means that your
>>> receiver is trying to pick up a very weak or non-existent signal,or the
>>> satellite position as programmed is off.
>>> In order to get a good digital lock,you will in most likely have to
>>> repeak the skew and or positional settings.Since I have a 920 receiver
>>> and not a 905,I am unsure as to try and help you with this
>>> specifically.But going into the tuning menu,pressing OPTIONS 6,4,4 and
>>> "keying" on the particular satellite will bring up the tuning meter
>>> which is a basic signal number which is 90 for best reception,and a
>>> signal quality number which generally has to be 15 or higher for a
>>> stable signal to lock onto.Press the positional display (EAST/WEST) in
>>> TINY amounts to see if the quality number raises or dips and act
>>> accordingly.Do the same for skew. Once you get the numbers in a high
>>> enough range,and the signal DC light remains on without dropping
>>> out,then save the position as indicated by the question below the tuning
>>> controls.
>>> This all assumes however that your dish tracks the arc correctly.If it
>>> does not,then you will need to redefine the arc at the dish,and maybe a
>>> technician will be required.
>>>
>>
>>
>
>