External Hard disk Not Detected

Status
Not open for further replies.

Roshin

Estimable
Aug 16, 2014
3
0
4,520
1
I have the Seagate 1TB backup plus external hardisk. Recently when i plug it into my laptop(USB 3.0) the hard disk is not detected ,ie its not showinng up in my computer ,its not in disk management. In device manager ,under storage controllers ,"USB Attached SCSI (UAS) Mass Storage Device" comes up when i connect the hdd, other than that the hdd is not detected and also the led on hdd does not come on. It works fine on other laptops and pc. I have another one of the same hdd which works fine on my machine ...If anyone can tell me the problem here ty
 

Roshin

Estimable
Aug 16, 2014
3
0
4,520
1
I solved the problem ..all i had to do was go to device manager -> under storage controllers selected the "USB Attached SCSI (UAS) Mass Storage Device" which comes up when i connect the drive -> right click and select update driver software ->browse my computer option -> let me pick ... option -> in the listed drivers i selected mass storage device and clicked OK. Everything works fine now ..
 

Tom Tancredi

Honorable
May 9, 2013
404
0
11,960
100
What happens when you plug it into any OTHER USB port? Can you detect it then? If not, then the ext drive is DOA most likely. The next test would be to plug it into another different PC / Mac and see if IT can see the drive contents. If not then you confirmed either the USB 3.0 cord is dead or the drive is.
 

Roshin

Estimable
Aug 16, 2014
3
0
4,520
1


All the ports are USB 3.0 and the drive was not detected with them too .The other ports are working (i use them for pen-drives ,mouse etc) ...the external drive works on other PC ....neither the drive nor the cord is dead. The external drive is ok now, it started working again when i updated the driver as mentioned earlier.
 

Ashik metha

Estimable
Apr 20, 2015
1
0
4,510
0
Roshin, in the drop down list, I don't find any options like storage devices. I can find only c:\program files(x86)\realtek\nicdrv_8169\win8. What should I do?
 

Jovz

Estimable
Jun 1, 2015
2
0
4,510
0
Thank you so much Roshin, I just followed your instructions and my external hdd is back to being detected. I was worried when it wasn't detected cause in the past, I read that it was corrupted paths that lead me to do a tiresome copy-paste mode in a linux OS. Your solution is very easy to follow and the best, my external Seagate 1TB is now detected :D
 

AgentOO7

Estimable
Jun 9, 2015
1
0
4,510
0


The only option listed is 'USB Attached SCSI (UAS) Mass Storage Device' on my Win8.1, unless I uncheck 'Show compatible devices only' When I uncheck it, there is no sign of the Mass storage driver to select. Manually pointing it to the usbstor.inf does not help either. It states the driver is not for the device. Similar to the OP, I have a Seagate drive, but it is 4TB.

Any insight on what you guys did to accomplish changing the driver to the USB Mass Storage Device ?

 

Jovz

Estimable
Jun 1, 2015
2
0
4,510
0

That is the one!

  • ■Device Manager
    ■USB Attached SCSI (UAS) Mass Storage Device (with Yellow Exclamation Point)
    ■right-click update driver software
    ■browse my computer for driver software
    ■let me pick from a list of device drivers on my computer
    ■make sure "Show compatible hardware" is checked the only one listed is "USB Attached SCSI (UAS) Mass Storage Device" click that then next and it will install and you are done.
I'm using Windows 8 and YES that is also the only one that shows on my pc so just click that "USB Attached SCSI (UAS) Mass Storage Device" then next.

If it's successful good

If not unplug external hdd -> restart pc -> plug again (do check if the hdd light is on/blinking) -> wait for like 2-3mins if the hdd is detected/installed (if not do the process again).
 

j_herndon

Estimable
Aug 26, 2015
1
0
4,510
0


So you selected the "USB Attached SCSI (UAS) Mass Storage Device", the update timed out on me....
 

murrayzz1

Estimable
Oct 9, 2015
1
0
4,510
0
I had this problem, tried this solution and it didn't work. The drivers would install, but the drive would still not be recognised.

Then, whilst trying it again, I accidentally disconnected the drive while the drivers were installing. The installation, which had been taking a while, completed almost immediately.

Lo and behold, when I plugged the drive back in again, Windows recognised it. I then tried this again on another computer which had the same problem and it worked again. Something about dismounting the drive during the driver installation and remounting it immediately afterwards seemed to do the trick.
 
Status
Not open for further replies.