i have a dude i paste this data of a disk
used 2 tools
1- whit drive fitness tool
failure code 0x73 excessive shock
technical result code
730078bc
2- via smart everest
--------[ SMART ]-------------------------------------------------------------------------------------------------------
[ Hitachi HDS721010KLA330 (GTF002PAKWK1VF) ]
01 Raw Read Error Rate 16 96 96 65543 OK (el valor es normal)
02 Throughput Performance 54 100 100 0 OK (el valor es normal)
03 Spin Up Time 24 142 142 43123015 OK (el valor es normal)
04 Start/Stop Count 0 100 100 24 OK (siempre funcionará)
05 Reallocated Sector Count 5 100 100 0 OK (el valor es normal)
07 Seek Error Rate 67 100 100 0 OK (el valor es normal)
08 Seek Time Performance 20 123 123 37 OK (el valor es normal)
09 Power-On Time Count 0 97 97 22325 OK (siempre funcionará)
0A Spin Retry Count 60 100 100 0 OK (el valor es normal)
0C Power Cycle Count 0 100 100 21 OK (siempre funcionará)
C0 Power-Off Retract Count 0 100 100 141 OK (siempre funcionará)
C1 Load/Unload Cycle Count 0 100 100 141 OK (siempre funcionará)
C2 Temperature 0 139 139 12, 43 OK (siempre funcionará)
C4 Reallocation Event Count 0 100 100 0 OK (siempre funcionará)
C5 Current Pending Sector Count 0 100 100 0 OK (siempre funcionará)
C6 Off-Line Uncorrectable Sector Count 0 100 100 0 OK (siempre funcionará)
C7 Ultra ATA CRC Error Rate 0 200 200 0 OK (siempre funcionará)
used 2 tools
1- whit drive fitness tool
failure code 0x73 excessive shock
technical result code
730078bc
2- via smart everest
--------[ SMART ]-------------------------------------------------------------------------------------------------------
[ Hitachi HDS721010KLA330 (GTF002PAKWK1VF) ]
01 Raw Read Error Rate 16 96 96 65543 OK (el valor es normal)
02 Throughput Performance 54 100 100 0 OK (el valor es normal)
03 Spin Up Time 24 142 142 43123015 OK (el valor es normal)
04 Start/Stop Count 0 100 100 24 OK (siempre funcionará)
05 Reallocated Sector Count 5 100 100 0 OK (el valor es normal)
07 Seek Error Rate 67 100 100 0 OK (el valor es normal)
08 Seek Time Performance 20 123 123 37 OK (el valor es normal)
09 Power-On Time Count 0 97 97 22325 OK (siempre funcionará)
0A Spin Retry Count 60 100 100 0 OK (el valor es normal)
0C Power Cycle Count 0 100 100 21 OK (siempre funcionará)
C0 Power-Off Retract Count 0 100 100 141 OK (siempre funcionará)
C1 Load/Unload Cycle Count 0 100 100 141 OK (siempre funcionará)
C2 Temperature 0 139 139 12, 43 OK (siempre funcionará)
C4 Reallocation Event Count 0 100 100 0 OK (siempre funcionará)
C5 Current Pending Sector Count 0 100 100 0 OK (siempre funcionará)
C6 Off-Line Uncorrectable Sector Count 0 100 100 0 OK (siempre funcionará)
C7 Ultra ATA CRC Error Rate 0 200 200 0 OK (siempre funcionará)